The Poor Man’s RF Probes

While working on my thesis I often have to measure signals up into 2.45 GHz range be it testing a mixer or determining the transfer function of a filter.  At such high frequencies standard banana jack or alligator clip cables turn into antennas which render any measurements done with them pretty much useless.  I get around this inconvenience by using what the engineers I worked with last summer called “Poor Man’s RF Probes.”  These probes are very easy to use and you can make a pair of your own for $10 assuming you already have shielded BNC to SMA cables and a few SMA billets.  Semi-rigid SMA male to male cables are used to make the probes themselves; here’s a link to the ones that I’m using. There may be cheaper cables out there and if you can find them I’d love to hear about it but in order to make the probes the outer jacket needs to be exposed in order to solder it directly to ground.

To make the probes themselves first cut the semi-rigid cable just below each SMA jack leaving a small amount of shielded cable to strip.  Figure 1 below shows two of the probes I am using at the moment next to an uncut cable and a Digi-Key label for reference.  Each probe is just over an inch long or so giving me enough room to strip the ends and bend the probe as needed while still keeping the overall length short enough to ensure quality measurements.

Figure 1: Semi-Rigid SMA Cable Cut to Length

When stripping the cut cable, I’ve found the easiest way to strip the rigid outer jacket is to use needle nose pliers.  Gripping the end of the jacket with the tip of the pliers and slowly bending it back and forth a few times is usually enough to cause the jacket to break all the way around the cable and you can then just slip it off leaving the center conductor insulator exposed.  The center conductor insulator can be stripped using standard wire strippers (~ 20 Gauge).  The goal is to minimize the amount of exposed center conductor keeping the probe close to the measurement point. I recommend practicing on the unusable  middle portion of the cable that will be left over to get the hang of it before stripping the probes themselves.

Once you get the probes themselves made, figure out where you’re actually placing the probes on your board next. Look for a relatively open area of ground plane close to the pad where you will be measuring from.  Bending the stripped probe slightly is necessary for both a good ground connection and the probe’s mechanical stability.  Note: It’s possible to snap the center conductor from too much bending resulting in a useless probe that will only cause headaches later on so bend with care.

Once you’ve determined where you are going to solder down the probe, use a hobby knife or similar tool and carefully scrape away the solder mask on the ground plane near the measurement site.  Be gentle but firm when scrapping because gouging the board too deeply could short the ground plane to any internal layers that might be in your board.  Figure 2 shows what the site around the input to my filter where I’m placing the probe.  In the picture, I’m placing the conductor of the probe on the unpopulated pad of R2 making use of the 0Ω resistor trick.

My apologies for the so-so photo quality during the remainder of this post; my camera phone only works so well…

Figure 2: Scraped GND Plane Solder Mask Near Probe Site

The third step of the process is to solder down the center conductor of the stripped SMA cable. Usually I’ll tin the pad with a little solder before placing the probe, blob some solder on the iron and while holding the probe in my fingers, tack solder the center pin down (Figure 3).  Note: The probe should be able to stand on its own right now but I wouldn’t move the board or probe too much as you could lift the pad the center conductor is soldered down to.

Figure 3: Tack Soldered Center Conductor

The next to last step is to solder the exposed ground plane to the outer metal jacket of the probe for a solid ground connection.  This will also make the probe mechanically sound so you can now make sure the center conductor is properly soldered down without worry. Note: This step can be done before the previous step if you so choose.  Just don’t be like me and hold the probe with your fingers because if you’re not quick you get burned.  I find this method easier as it make shorting the center conductor to ground less likely.

Figure 4: Soldered Ground Connection

Finally before you can consider yourself done, use a multi-meter and make a quick continuity check. Be sure the center conductor is not shorted to ground and that it is actually connecting to the node you would like it to.  Note: If you have to desolder the probe because of a short or to remove it altogether desolder the center conductor first to avoid lifting the pad.

If you treat these probes with a little care they should last you long enough to justify their cost.  After enough wear and tear though they will become unusable and have to be replaced.  I’ve been using the same two probes for over six months now with no lose in measurement quality and they’ve been removed and resoldered quite a few times.  Before each use however, I do recommend checking the continuity of the center conductor just to be sure it’s still good. Troubleshooting a bad probe isn’t exactly fun and can make you lose your hair when your circuit mysteriously stops working.

Figure 5: Final Probe Placement for Filter Testing


6 responses to “The Poor Man’s RF Probes

  • Stephen Trier

    Those are some good tricks. I use similar ones. Those SMA-F to SMA-F adapters you pointed out can be hard to separate without damaging the threads. Have you tried bulkhead adapters instead? They are are essentially the same, but with a hex-wrench-friendly surface in the middle that gives you something to hold onto when connecting or disconnecting either end.

    As for the Digi-Key cables you make your probes from, good observation! I have had a tech I work with make probes like these from bulk coax & connectors, but never thought to look for pre-assembled cables to cut apart and save time. Thanks for the idea!

    • FakeEEQuips

      Glad to help out! I haven’t looked at those bulkhead adapters before but I’ll keep them in mind for the next time I need to stock up on probe parts. Typically, if the connectors get stuck I’ll use some pliers to hold to the probes I’ve soldered to the board in place and twist the rest of the assembly.

  • rfdave

    When you’re feeling a need for some accuracy, and are using a network analyzer, you can short out the center conductor to the shield, and use port extensions on the network analyzer to set the short at the appropriate place on the smith chart. Solder it down, and you’ve got a pretty good calibrated measurement

    • FakeEEQuips

      My usual cal for the network analyzer is to use the open, short, and load standards before using port extensions with my custom probes. That was another trick I learned from last summer and you’re right, it does make for a pretty good calibrated measurement.

      I actually learned today how to properly take measurements on my filter using only a signal generator and a spectrum analyzer though my impedances may have been slightly mismatched between the filter output and spec an.

  • Philip Freidin

    I make extensive use of these parts (digikey): H9173CT-ND

    With landing zones on the pcb at places I think I might want to probe.
    They are really tiny, and good to 6 GHz.

    For cables, I use these (or shorter/longer versions): H9170-ND

    I cut these in half, and terminate the cut end in either an SMA of BNC connectors.

    The H9173CT-ND connectors can also be added to a PCB with probably
    slightly less effort that the coax attach method you show.

    The advantage over the technique you use (and I have too) is that the parasitics are minimal when you unplug the cable (or just don’t place the connector), and no chance of accidentally ripping up a PCB trace.

    I also use these connectors for some VNA work such as testing PCB antennae, and have made Short/Open/Load test boards with 3 of these connectors on them.

    Since I am writing about probing, I also use special low noise scope probe connectors from Tek 131-4244-00 (bag of 100 connectors, match P6139A probes) for probing up to 500 MHz, with very low ground impedance.

    • FakeEEQuips

      That’s a pretty slick system you use, I wasn’t even aware connectors like those SMD coax ones existed. I’ll have to keep those in mind if I ever layout another RF board. Thanks for sharing!

Leave a Reply to Philip Freidin Cancel reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s